Repeater

Point-to-Point Wireless Repeater Unit

Repeater

Point-to-Point Wireless Repeater Unit, Add up to 15 Repeaters to your Twin Link System

SKU: P2P-R Category: Tags: , ,

Share This Product

What it does

Extends the wireless range of the Twin Link by relaying data between the input and output nodes.

The perfect addition to your Twin Link

The Point-to-Point Repeater is the perfect addition to a Twin Link system where the Input and Output nodes are out of range, or a line of sight connection is interrupted by buildings or hilly terrain. It works by retransmitting incoming signals from other nodes in the network, enabling you to boost your range and navigate around obstacles.

  • Extend the range of your Twin Link by up to 1.5km (0.9mi) line-of-sight (using default antenna)
  • Get around buildings by positioning Repeaters at corners
  • Add up to 15 repeaters in a single Point-to-Point system
  • Simple integration with your existing Twin Link system

See It In Action

In this example, a wireless link is needed between a reservoir and a pump station. The Input Node will measure the incoming 4-20mA signal from the reservoir level sensor, and the Output Node will output 4-20mA to the pump controller, which will switch the pump on and off (thus controlling the water levels in the reservoir).

The reservoir is over a hill, so there is no line of sight between it and the pump station. By placing a Repeater at the top of the hill within line of sight of both the Input and Output nodes, a successful link can easily be made.

Simple Integration Using Mesh IDs

Network connections between P2P nodes are established using a Mesh ID code, which is printed on the product label. Integrating a Repeater into your Twin Link system is as simple as making sure that its Mesh ID code matches the code printed on the pre-paired Input and Output nodes, and then powering the units on.

Setting the Repeater‘s Mesh ID is simple and takes less than a minute using our ToolBox software and the USB Bridge Key (sold separately). Once the Mesh ID’s are matched, and all units in the system are in range and line of sight, the new node will be automatically included in the network.

5 Year WarrantyR-NZ E2180CEFCC 2ACTT-1409

Specifications

Transmission


RF data rate: 250Kb/s


RF frequency range: 2405-2475MHz


RF transmission power: +20dBm (Optional low power setting [10dBm] selectable in software)


Transmission range: Up to 0.9mi (1.5km) LOS with supplied antenna (WG-3DBI). All nodes must be set to full power (+20dBm) for max range. Transmission distance may be limited by regional power restrictions.


RF receiver sensitivity: -110dBm


Number of RF channels: 15


Number of wireless nodes: Up to 17 nodes per mesh (Twin Link plus up to 15 Repeaters)


Spreading method: Direct sequence


Modulation: O-QPSK


Power


Power supply: 9–36V DC, 2.5VA max


Programming


Define ToolBox: Simple software programming using Define ToolBox, via the Twin Link Input Node (Bridge Key required, sold separately)


Construction


Casing: 35mm DIN rail mount casing. Installation Category II; Pollution Degree 2; Flame resistant


Ingress protection rating: IP20 – install in a protective enclosure


Dimensions (H x W x D): Unit body: 3.98 x 0.91 x 4.72″ (101 x 23 x 120mm), With included antenna: 5.91 x 0.91 x 5.75″ (150 x 23 x 146mm)


Weight: 4oz (113g), with included antenna and plugs



Environmental Conditions


Operating temperature: -4 to 131°F (-20 to 55°C)


Storage temperature: -4 to 149°F (-20 to 65°C)


Operating humidity: 0–85% non-condensing


Altitude: 2187yd (2000m)


Certifications & Compliances


FCC ID: 2ACTT-1409: 47 Code of Federal Regulations; Part 15 – Radio Frequency Devices; Subpart C – Intentional Radiators, including Section 15.247 – Operation in the band 2400 –2483.5MHz


SAS/ANS 4268:2012: Radio equipment and systems – Short range devices – Limits and methods of measurement


ETSI EN 300 440-2, V 1.4.1, 2010: Electromagnetic compatibility and Radio spectrum matters (ERM); Short Range Devices (SRD); Radio equipment to be used in the 1GHz to 40GHz frequency range; Part 2: Harmonised EN under article 3.23 of the R&TTE Directive


EN 301 489-3 V1.6.1, 2013: Electromagnetic compatibility and Radio spectrum Matters (ERM); Electromagnetic Compatibility (EMC) standard for radio equipment and services; Part 3: Specific conditions for Short Range Devices (SRD) operating on frequencies between 9kHz and 40GHz

Documents

Repeater Manual 16V01, 04-Aug-2016 | (190 KB)
Twin Link Manual 17V01, 04-May-2017 | (2059 KB)
P2P-R (Repeater) Datasheet 17V01, 28-Apr-2017 | (1092 KB)

Software


Define ToolBoxDefine ToolBox

Smart, simple software to program your non-Zen series products

Use Define ToolBox software to program your non-Zen series product via your PC. It configures:

ToolBox offers a simple interface for connecting to your compatible device, and a range of flexible configuration options, including an extensive library of pre-calibrated ranges and linearization tables for advanced scaling.


Define ToolBox Configuration Software

Order Codes

P2P

P2P-R Point-to-Point wireless repeater unit
P2P-TWIN-LINK Point-to-Point paired I/O units (P2P-I + P2P-O)

Accessories/Software

Bridge Key USB Bridge Key and communications kit (required for software configuration) Not FCC approved.
Sold separately
Antenna Upgrades Click here for antenna upgrade options
Define ToolBox Simple utility for setting up your Point-to-Point system Free download

All prices are in US Dollars. For pricing in other currencies, please contact us.